Semester 1 : Chapter 9

Question 1:
What should be used to mount cable to a wall?

A.   tie wraps
B.   electrical tape
C.   staples
D.   paperclips

Question 2:
What type of raceway should be used if it will be visible in the room?
A.   channel guide
B.   decorative
C.   ladder rack
D.   gutter

Question 3:
Why is the wiring sequence critical when RJ-45 jacks are used at the telecommunications outlet in a horizontal cabling scheme?
A.   For the network to function properly.
B.   Improper wiring sequence will short out the connection.
C.   You could get a nasty electrical shock.
D.   The collision rate is adversely affected.

Question 4:
Why are split pairs a problem for network installations?
A.   The wires are unshielded and easily lose synchronicity.
B.   The wires are part of different circuits so signals are not protected and cross-talk occurs.
C.   The wires are part of different circuits and easily shorted out by power spikes.
D.   It is difficult to detect split pairs which requires performing a wire map.

Question 5:
What is the central junction for the network cable?
A.   POP
B.   server
C.   center point
D.   wiring closet

Question 6:
How is an RJ-45 jack surface mounted?
A.   with a punch tool
B.   with Velcro
C.   flush with the surface
D.   adhesive backed or screw box

Question 7:
What is one advantage of using distribution racks for mounting patch panels?
A.   allows easy access to both the front and back of the equipment
B.   provides neutral ground
C.   inexpensive compared to brackets
D.   requires minimal wall space

Question 8:
What is a rough diagram that shows where the cable runs are located called?
A.   cut sheet
B.   sketch
C.   cable plan
D.   cabling route

Question 9:
Which best describes a patch panel's function?
A.   It serves as a temporary fix to network problems.
B.   It acts as a router for temporary networks connecting the various devices often found at conventions and shows.
C.   It acts as a switchboard where horizontal cabling from workstations can be connected to other devices to form a LAN.
D.   It allows the network administrator to test the entire network cabling from a single location.

Question 10:
When should cable not be routed in an existing raceway?
A.   if the raceway distance exceeds 100 feet
B.   if the raceway material is partially metallic
C.   if it already contains a power cable
D.   if it contains a telephone line

Question 11:
All the items below are personal safety precautions before you install cable except :
A.   Wear long sleeves.
B.   Wear long pants.
C.   Wear baggy clothes.
D.   Check for power cables.

Question 12:
What tool would you use to attach CAT5 cable to a patch panel?
A.   110 patch tool
B.   cable terminator
C.   punch tool
D.   patch terminator

Question 13:
Which of the following describes a cable tester measurement of signal attenuation?
A.   It measures the reduction in power of a signal received from a signal injector.
B.   It measures the increase in power of a signal received from a signal injector.
C.   The signal injector attaches to the near end of the cable.
D.   The frequency to be used for testing is specified in EIA/TIA 568A.

Question 14:
What should be done when preparing to run cable?
A.   Cut the cable before pulling it.
B.   Unroll it before pulling it through the ceiling.
C.   Label the boxes and cable.
D.   Take the cable out of the boxes.

Question 15:
When running cable from the wiring closet to wall jacks, where is the cable itself labeled?
A.   at each tie
B.   at each end
C.   at the jack end
D.   at the panel end

Question 16:
If you have one wiring closet and you want to add more, what name is given to additional wiring closets?

A.   IDFs
B.   MDFs
C.   Extended Stars
D.   POPs

Question 17:
How many pins are on each of the ports of a patch panel?
A.   4 pins
B.   8 pins
C.   11 pins
D.   45 pins

Question 18:
What is the most important thing to do before you work in walls, ceilings or attics?
A.   Label the faceplate.
B.   Measure out the cable.
C.   Turn off power to the area.
D.   Install the patch panel.

Question 19:
Why is establishing a baseline performance level for a network important?
A.   for fulfilling one of the requirements necessary for you to get your network certification
B.   for providing your client with proof of a successful installation
C.   for future periodic testing of the network and diagnostics
D.   for obtaining a network registration and identification number from TIA/EIA and IEEE

Question 20:
What is the first thing you should do if near-end crosstalk is detected?
A.   Redo all connections at the patch panel.
B.   Isolate which connection is the cause by running a TDR test.
C.   Redo all connections at the cross connects.
D.   Visually check the horizontal cabling.

Question 21:
What kind of jack must be used for making a connection to a Category 5 unshielded twisted pair cable in a horizontal cabling scheme?
A.   RJ-45
B.   BNC
C.   UTP 55
D.   EIA 45

Question 22:
Which of the following is a source that can produce interference on UTP cable?
A.   fluorescent lights
B.   fiber-optic cabling
C.   bridges
D.   coaxial cabling

Question 23:
What kind of a cable must you use when laying cable through spaces where air is circulated?
A.   shielded
B.   double coated
C.   fire rated
D.   unshielded

Question 24:
Why shouldn't you install a jack in the bottom five centimeters of a wooden baseboard?
A.   The bottom plate of the wall will prevent you from pushing the box into the baseboard.
B.   Most floors have metal supports that produce electromagnetic interference when close to the jack.
C.   Dust and dirt accumulate under it that can then get into the connection and affect network performance.
D.   It's so close to the floor, there isn't enough space for most people to work and manipulate the wires.

Question 25:
How does a cable tester (a TDR) measure distance?
A.   The cable tester identifies signal degradation, indicating the cable is longer than the acceptable maximum length.
B.   It determines the time a signal takes to be reflected back from closed-ended cable.
C.   It times the signal sent towards and reflected back from the end of an open-ended cable.
D.   It measures the ability of other devices on the network to receive and send signals through the cable.