Question 1:
Which of the following is provided by the show version command?
A. Information about the IP addresses of the interfaces
B. Information about the routing protocol
C. Information about the system image file
D. Information about the default gateway

Question 2:
Which command is used to discover the configuration register setting?
A. show register
B. show running-config
C. show version
D. show startup-config

Question 3:
Which command is used to configure a routing protocol?
A. Router# rip network 192.11.10.0
B. Router(config)# router rip
C. Router(config)# routing rip
D. Router(config)# routing protocol rip

Question 4:
Where does the router search for the IOS software if the Flash is empty?
A. ROM
B. RAM
C. NVRAM
D. TFTP server

Question 5:
You are upgrading the IOS on a router, which command would be used to copy the new IOS image from a network server?
A. Router# copy flash tftp
B. Router# copy tftp flash
C. Router# copy startup-config tftp
D. Router# copy tftp startup config

Question 6:
Which command is used to tell the router to boot from flash?
A. Router# boot flash IOS_filename
B. Router# boot system flash IOS_filename
C. Router(config)# boot flash IOS_filename
D. Router(config)# boot system flash IOS_filename

Question 7:
In the Cisco IOS name cpa25-cg-1, what does cpa25 represent?
A. Where the image runs
B. Platform on which the image runs
C. Special capabilities and feature sets
D. Whether the image has been compressed

Question 8:
Which of the following correctly describes a method for specifying how a router loads the Cisco IOS software?
A. Designate fallback sources for the router to use in sequence from NVRAM.
B. Configure the Cisco IOS software image for the location where it will bootstrap.
C. Manually boot a default system image at a virtual terminal.
D. Manually boot a default system image at the network server.

Question 9:
Which configuration register mode is used to tell the router to boot from ROM?
A. 0x---0
B. 0x---1
C. 0x---2
D. 0x---3

Question 10:
Which command can be used to configure a router's Ethernet port?
A. int E0 ip address
B. int E0 ip address subnet mask
C. int S0 ip address
D. int S0 ip address subnet mask

Question 11:
Which configuration register is used on a Cisco 2500 series router during password recovery?
A. 0x2100
B. 0x2101
C. 0x2102
D. 0x2142

Question 12:
Which configuration register mode is used to tell the router to boot from NVRAM?
A. 0x---0
B. 0x---1
C. 0x---2
D. 0x---N

Question 13:
Which command is used to view the name of the system image file?
A. Router# show flash
B. Router# show register
C. Router# show running-config
D. Router# show startup-config

Question 14:
Which step should be performed before copying software between the TFTP host and Flash memory?
A. Use the show Flash command to check connectivity to the server
B. Check that you can see and write into RAM memory
C. Verify that there is sufficient room in Flash to accommodate the IOS
D. Check the configuration file name and location on the network server

Question 15:
Which command is used to tell the router to boot from ROM?
A. Router# boot system rom
B. Router# boot system rom IOS_filename
C. Router(config)# boot system rom
D. Router(config)# boot system rom IOS_filename

Question 16:
Which configuration register mode is used to tell the router to boot from ROM monitor mode?
A. 0x---0
B. 0x---1
C. 0x---2
D. 0x---3

Question 17:
Which command can be used to check the boot field setting?
A. Router# show version
B. Router# show register
C. Router# show running-config
D. Router# show startup-config

Question 18:
Which command is used to change the default configuration register setting?
A. Router# register value
B. Router# config-register
C. Router(config)# register value
D. Router(config)# config-register

Question 19:
In the Cisco IOS name cpa25-cg-1, what does cg represent?
A. Where the image runs
B. Platform on which the image runs
C. Special capabilities and feature sets
D. Whether the image has been compressed

Question 20:
Where will the router search for the IOS software if there are no boot system commands in NVRAM?
A. ROM
B. RAM
C. Flash
D. TFTP server

Question 21:
Which of the following is NOT part of the Cisco IOS naming convention?
A. Where the image runs
B. Platform on which the image runs
C. Special capabilities and feature sets
D. Amount of space the file will use when copied to NVRAM

Question 22:
Which command is used to copy a system image to a network server?
A. Router# copy flash tftp
B. Router# copy tftp flash
C. Router(config)# copy flash tftp
D. Router(config)# copy tftp flash

Question 23:
Which command is used to tell the router to boot from a network server?
A. Router# boot tftp IOS_filename ip address
B. Router# boot system tftp IOS_filename ip address
C. Router(config)# boot tftp IOS_filename ip address
D. Router(config)# boot system tftp IOS_filename ip address

Question 24:
Which command can be used to check the amount of system memory available?
A. Router# show flash
B. Router# show interface
C. Router# show register
D. Router# show running-config

Risposte: CCBDB DBABB DCACC AADCC DADA