Question 1:
Information regarding routes has been received on a router through interface A. Which routing technique will prevent this information from exiting on the router through the same interface A?
A. Dynamic routing
B. Split horizon
C. Static routing
D. Hold down timers

Question 2:
What do distance vector algorithms require of routers?
A. Default routes for major internetwork nodes in case of corrupted routing tables
B. Periodically send its routing table to its neighbors
C. Fast response times and ample memory
D. Maintain a full database of internetwork topology information

Question 3:
What is one advantage of dynamic routing?
A. Takes little network overhead and reduces network overhead traffic
B. Reduces unauthorized break-ins as security is tight
C. Adjusts automatically to topology or traffic changes
D. Requires very little bandwidth to operate efficiently

Question 4:
Which metrics are commonly used by routers to evaluate a path?
A. EMI load, SDLC connections, deterioration rate
B. Bandwidth, load, reliability
C. Distance, hub count, SN ratio
D. Signal count, loss ratio, noise

Question 5:
Which best describes link-state algorithms?
A. Enables each router to know the exact topology of the entire participating internetwork.
B. Requires minimal router CPU utilization.
C. Determines distance, direction and reliability to any link on the internetwork.
D. Uses little network overhead and reduces overall traffic.

Question 6:
Which OSI Layer is responsible for path determination?
A. 1
B. 2
C. 3
D. 4

Question 7:
How are link-state routing updates triggered?
A. By timers
B. By topology changes
C. By protocol changes
D. By changing the NIC

Question 8:
Which routers exchange information when using a distance-vector routing protocol?
A. All
B. All in network
C. All in subnetwork
D. Only neighbors

Question 9:
Which best describes convergence?
A. When messages simultaneously reach a router and a collision occurs
B. When several routers simultaneously route packets along the same path
C. When all routers in an internetwork have the same knowledge of the structure and topology of the internetwork
D. When several messages are being sent to the same destination

Question 10:
What is one disadvantage of dynamic routing?
A. Requires lots of active network administrator management
B. Can reveal everything known about an internetwork
C. Must be reconfigured if the network is changed or stations are added
D. Cannot compensate for network failures so crashes can be a recurring problem

Question 11:
Which protocol is a link-state routing protocol?
A. EIGRP
B. OSPF
C. RIP
D. IGRP

Question 12:
Which term describes the situation where packets never reach their destination but instead cycle repeatedly through the same group of network nodes?
A. Split horizon
B. End to end messaging
C. Convergence
D. Routing loop

Question 13:
What does a router use to identify the destination network (LAN) of a packet within an internetwork?
A. MAC address
B. Port address
C. SPX address
D. Network address

Question 14:
Which metric measures the passage of a data packet through a router?
A. Exchange
B. Hop
C. Transmittal
D. Signaling

Question 15:
What will happen if routers have different sets of LSAs?
A. A check sum procedure is initiated and faulty routing tables repaired.
B. Routes become unreachable because routers disagree about a link.
C. A comparison is forced and subsequent convergence on a single routing table occurs.
D. A broadcast message is sent with the master copy of the routing table to all routers.

Question 16:
What is one disadvantage of static routing?
A. Requires a name server on each network
B. Routing of data stops while routers exchange routing tables
C. The network administrator must manually update the routing table whenever a topology change occurs
D. Tends to reveal everything known about an internetwork

Question 17:
Which protocol is a hybrid routing protocol?
A. EIGRP
B. OSPF
C. RIP
D. IGRP

Question 18:
Why are hold-down timers useful?
A. They help prevent a router from immediately using an alternate route that includes the failed route
B. They force all routers in a segment to synchronize switching operations
C. They reduce the amount of network traffic during high traffic periods
D. They provide a mechanism for bypassing failed sections of the network

Question 19:
What best describes the difference between a routed protocol versus a routing protocol?
A. Routed protocols are used between routers to maintain tables while routing protocols are used to carry user data.
B. Routed protocols use distance vector algorithms while routing protocols use link-state algorithms.
C. Routed protocols are used to carry user data while routing protocols maintain tables.
D. Routed protocols use dynamic addressing while routing protocols use static addressing.

Question 20:
Which kind of route is set when the next hop is not explicitly listed in the routing table?
A. Dynamic
B. Default
C. Passive
D. Incremental

Question 21:
Which routing protocol maintains a complex database of topology information and uses link-state advertisements (LSAs)?
A. RIP
B. IGRP
C. OSPF
D. EIGRP

Question 22:
How can the count to infinity problem be prevented?
A. By using routing loops
B. By defining a minimum hop count
C. By increasing router memory
D. By using hold-down timers

Question 23:
Which part(s) of an IP address is used by the router for path determination?
A. Network
B. Network and client
C. Network, subnetwork, and host
D. Network, subnetwork, host, and subnet mask

Question 24:
What is a network with only one path to a router called?
A. Static network
B. Dynamic network
C. Entity network
D. Stub network

Risposte: BBCBA CBDCB BDDBB CAACB CDAD